CGDI MB RepairsReset Mercedes W211 Rolling Code Step by Step

How-to: repair Mercedes W211 original EIS rolling code with CGDI Prog Mercedes Benz key programmer.

Rolling code :
A rolling code (or sometimes called a hopping code) is used in keyless entry systems to prevent replay attacks, where an eavesdropper records the transmission and replays it at a later time to cause the receiver to ‘unlock’. Such systems are typical in garage door openers and keyless car entry systems.

Why need repair W211 rolling code?
Most of keys are too fast to be inserted and removed,  the track code does not roll, resulting in code rolling, so the key and the EIS cannot be matched properly. Car key programmer CGDI MB has the ability to repair Mercedes rolling code.

Tools required:
CGDI Prog MB
Analog key data collector
OBD connector
USB cable

Follow main steps below:
1. First you need a key password
2. Calculate the track code of the key
3. Read the EIS, fill in password and save data
4. Calculate the erase password and erase it
5. Load the EIS data with the password
6. Click “Allow modification of data”
7. Change the track code of the key position to the track
code of the key.
8. Write data
9. Learn key

Step-by-step procedure:

1. Read key password. If there is no key,you can calculate the password by doing all keys lost

CGDI-mb-w211-hopping-code-3

Calculate password

CGDI-mb-w211-hopping-code-4

2.Calculate the track code of the key. Press Read Key/Chip and read current key information

CGDI-mb-w211-hopping-code-5
Fill in the password

CGDI-mb-w211-hopping-code-6

Click to get the track code

CGDI-mb-w211-hopping-code-7

Confirm that the key has been inserted into the CGDI MB and check that the key password is correct.

The track code calculated by the wrong password is invalid.

CGDI-mb-w211-hopping-code-8

Calculate key track code success

CGDI-mb-w211-hopping-code-9

3.Read EIS, enter password and save data

CGDI-mb-w211-hopping-code-10

CGDI-mb-w211-hopping-code-11

4.Calculate the erase password ad erase the EIS.

CGDI-mb-w211-hopping-code-12
CGDI-mb-w211-hopping-code-13

Press Wipe the EIS to erase EIS

CGDI-mb-w211-hopping-code-14

Insert the CGDI Prog IR adapter into the EIS within 30 seconds.

CGDI-mb-w211-hopping-code-15

Erase EIS success

CGDI-mb-w211-hopping-code-16

Read EIS and check current status

CGDI-mb-w211-hopping-code-17
The EIS is erased

CGDI-mb-w211-hopping-code-18

5. Press Load EIS data to load  saved data previously with key password
CGDI-mb-w211-hopping-code-19

CGDI-mb-w211-hopping-code-20

View the key position (key position is 1) and copy the track code
CGDI-mb-w211-hopping-code-21

Click on Allow data modification

CGDI-mb-w211-hopping-code-22 CGDI-mb-w211-hopping-code-23

7.Modify the track code of the key position to the track code of the key

CGDI-mb-w211-hopping-code-23

8.Write the EIS data

CGDI-mb-w211-hopping-code-24

Recommend to write the VIN first, then write the EIS data

CGDI-mb-w211-hopping-code-25
Insert the IR adapter into the EIS within 30 seconds

CGDI-mb-w211-hopping-code-26
Write EIS data successfully

CGDI-mb-w211-hopping-code-27

Read EIS data to check current key status
CGDI-mb-w211-hopping-code-28

Insert the original car key into EIS to learn key, the EIS can be activated

CGDI-mb-w211-hopping-code-29

Insert the key, wait 1-5 seconds, the ELV responds,  the EIS is activated and the key learnt successfully

Read EIS data again

CGDI-mb-w211-hopping-code-30

W211 EIS original rolling code is repaired by CGDI MB successfully.
CGDI-mb-w211-hopping-code-31

Done.

Be the first to comment

Leave a Reply

Your email address will not be published.


*